5 1 5 - 1 0 6 1 2-43 dialight corporation 1501 route 34 south farmingdale, nj 07727 tel: (732) 919-3119 fax: (732) 751-5778 www.dialight.co m 2 3 m m r o u n d ? o p t o p i p e t m o p t i c a l l i g h t p i p e , b i - l e v e l 13.97 [.55] 2.54 [.100] 1.91 [.075] ref 7.62 [.300] 1.57 [.062] diffused front surfaces; 2 plcs 5.08 [.200] 2.54 [.100] .25 [.010] 7.87 [.310] 5.12 [.200] 2.54 [.100] ? 1.63 [.064] mounting pin 9.14 [.36] 2.79 [.11] 4.57 [.18] 3.05 [.120] 1.52 [.06] ? 3.05 [.120] typ 2 plcs 5.12 [.200] 2.29 [.090] 4.50 [.177] 1.45 [.057] typ 1.60 [.063] typ [? .060 .002] typ, 2 plcs 2.54 .05 [.100 .002] 3.35 [.132] 4.27 [.168] 4.39 [.173] 4.50 [.177] typ 1.04 [.041] typ 3.89 [.153] 2.69 [.106] typ 2.54 .05 [.100 .002] 3.73 [.147] 4.39 [.173] typ figure a (using single color smt leds) figure b (using bi-color smt leds) this view shows two 515-1061 light pipes mounted side by side ?1.52 .05 [.060 .002] typ, 2 plcs direction of light direction of light recommended solder pad/holes layou t recommended solder pad/holes layout front panel dimensions in mm [inches] r e c o m m e n d e d m i c r o l e d s m t l e d s f o r u s e w i t h 5 1 5 - 1 0 6 1 p a r t n o . c o l o r p a g e # 597-3111-5xx algaas red 1-30 597-3211-5xx orange 1-30 597-3301-5xx green 1-30 597-3401-5xx yellow 1-30 597-7701-5xx red/green 1-31 597-7721-5xx yellow/green 1-31 f e a t u r e s can be mounted in arrays spaced .200 apart (min.) high transmissivity polycarbonate material ul94v-0 compliance esd protection (circuit isolation from front panel) wide viewing angle arrays reduce insertion costs allows bi-level smt indicators secures to pcb by press-fit l e d d a t a for absolute maximum ratings and other electrical and optical data on the recommended leds, refer to led data sheets. d i a l i g h t o p t o p i p e l i g h t p i p e d e s c r i p t i o n this optopipe? is a standard design intended as a smt compatible replacement for our 553 series circuit board indicators. the light outputs are spaced vertically .100" from the pcb to the first element, and then 0.200" between the top and bottom elements. we recommend a minimum of 0.200" between light pipes as a normal mounting pitch. this optopipe? is held in place by 2 press-fit pins along the bottom of the device. the light pipe is not attached to the panel at any point but can protrude through holes in the panel. the gently arcing emitting end sticks through the plastic or metal panel. the light source is dialight's 597 series type 1208 led. the light pipe material is water clear transmissive polycarbonate rated ul94-v0, and has a 35% oxygen index. dialight can provide custom optopipe? solutions for your applications. o p e r a t i n g / s t o r a g e t e m p e r a t u r e ?30c to +100c note: designed for post-reflow pc board insertion.
|
